United States Stove Company 2200I Instruction Manual

Owner’s Operation and Instruction ManualCSSUCOMPANYUNITED STATES STOVESAFETY NOTICE:If this heater is not properly installed, a house re may result.

10 UsscCHIMNEY CONNECTOR (STOVE PIPE)Your chimney connector and chimney must have the same diameter as the stove outlet (6”). If this is not the case,

Ussc 11CHIMNEYYour wood stove may be hooked up with a 6” factory built or masonry chimney. If you are using a fac-torybuiltchimney,itmustcomplyw

12 UsscFACTORY BUILT CHIMNEY :When a metal prefabricated chimney is used, the manufacturer’s installation instructions must be followed. You must als

Ussc 13MASONRY CHIMNEY :Ensure that a masonry chimney meets the minimum standards of the National Fire Protection As-sociation (NFPA) by having it ins

14 UsscCombustible Wall Chimney Connector Pass-ThroughsMethod A. 12” (304.8 mm) Clearance to Combustible Wall Mem-ber: Using a minimum thickness 3.5”

Ussc 15OUTSIDE COMBUSTION AIRYour wood stove is approved to be installed with an outside air intake which is necessary for a tightly constructed home

16 UsscTYPE WEIGHT(LBS. CU. FT., DRY)PER CORD EFFICIENCY RANKINGSPLITS MILLIONS BTU’s/CORDHickory 63 4500 1.0 Well 31.5White Oak 48 4100 .9 Fair 28.6R

Ussc 17THE FIRST FIRESThe fresh paint on your stove needs to be cured to preserve its quality. Once the fuel charge is properly ignited, only burnsma

18 UsscWARNINGS• NEVEROVERFIREYOURSTOVE.IFANYPARTOFTHESTOVESTARTSTOGLOWRED,OVERFIRINGIS HAPPENING. READJUST THEAIRINTAKECONTRO

Ussc 19ASH DISPOSALAshes should be removed from the stove every few days or when ashes get to 2 to 3 inches deep. Always empty the stove when it is co

2 UsscCONGRATULATIONS!You’ve purchased a heater from North America’s oldest manufacturer of wood burning products.By heating with wood you’re helping

20 UsscREPAIR PARTS189114017182019161523252624393536373827293028333431121314325 672342221104315672981011Feed Door Assembly

Ussc 21REPAIR PARTSKey Part No. Description Qty.1 25491 Feed Door, Painted (40484) 12 25692 Handle, Painted (40515) 13 83506 3/8 x 1-1/4 Roll Pin 14 8

22 UsscNOTES

Ussc 23NOTES

24 UsscTHISMANUALWILLHELPYOUOBTAINEFFICIENT,DEPENDABLESERVICEFROMYOURHEATER,ANDENABLEYOUTOORDERREPAIRPARTSCOR-RECTLY.KEEPTHISMANU

Ussc 3" CUT HERE " CUT HEREWARRANTY INFORMATION CARDName__________________________________________ Telephone #: (_____)_____________City____

4 Ussc" CUT HERE " CUT HEREÊ ÉFold Here Fold HereUnited States Stove CompanyP.O. Box 151South Pittsburg, TN 37380Fold HerePLACESTAMPHERE

Ussc 5Tools and Materials Needed For InstallationYou will need a drill with a 1/8” bit to install sheet metal screws into connector pipe. A 5/16” sock

6 UsscASSEMBLY INSTRUCTIONSBlower AssemblyTHE BLOWER ASSEMBLY MUST BE DISCONNECTED FROM THE SOURCE OF ELECTRICAL SUPPLY BE-FORE ATTEMPTING THE INSTALL

Ussc 7INSTALLATIONSAFETY NOTICE• IF THIS STOVE IS NOT PROPERLY INSTALLED, A HOUSE FIRE MAY RESULT. TOREDUCETHERISKOFFIRE,FOLLOWTH

8 UsscFLOOR PROTECTORYour wood stove should be placed on a 1 inch, non-combustible surface with a k factor of 0.84. For multiple layers, add R-values

Ussc 9CLEARANCES TO COMBUSTIBLESIt is of utmost importance that the clearances to combustible materials be strictly adhered to during installation of